+604-538 1998, +604-530 1998, +6012-498 2349






Integral Probe: No

Index Motion: Motorised

Max. Length: 450mm

Index Resolution: 7.5°

Index Positions: 720

Repeat. Indexing: Yes

Repeat. Stylus Change: Yes

PH10T (Fully Motorised Probe Head)

The PH10T is a fully motorised probe head that offers immediate indexing from 0° to 105° in the A axis and through 360° in the B axis to be moved to 720 repeatable positions in 7.5 degree increments. This probe head should be used by customers requiring frequent indexing or when more precise alignment to the features being measured is required.

Length 103 mm
Width 62 mm
Weight 645 g
Probe mounting M8 thread (2-wire)
Head mounting Shank to suit CMM
Suitable controller PHC10-3 PLUS
Repeatability of position 0.4 µm (0.00002 in) specified at a distance of 100 mm
Total number of positions 720
Maximum recommended drive torque 0.45 Nm
Maximum extension bar 300 mm (11.8 in) using PEL4 extension


TP20 Stylus Modules

A range of seven, application specific, probe modules is available and are identified by coloured caps.


  Application Trigger forces* Stylus lengths

SF- Standard force

TP20 SF module


Suited to the majority of applications

 XY: 0.08 N

 Z: 0.75 N

 Stylus: 10 mm

10 mm to 50 mm GF

LF- Low force

TP20 LF module


Low trigger forces applications - e.g. rubber seals

 XY: 0.055 N

 Z: 0.65 N

 Stylus: 10 mm

10 mm to 30 mm

MF- Medium force

TP20 MF module


Where a higher trigger force than standard is required

 XY: 0.1 N

 Z: 1.9 N

 Stylus: 25 mm

10 mm to 60 mm

EF- Extended force

TP20 EF module


Large stylus assemblies or where vibration causes spurious 'air' triggers

 XY: 0.1 N

 Z: 3.2N

 Stylus: 50 mm

10 mm to 60 mm

6W- 6-way

TP20 6W module


Measurement in the –Z direction - e.g. undercuts

 XY: 0.14 N

 Z: 1.6N

 Stylus: 10 mm

10 mm to 30 mm

EM1 STD- 50 mm extension

TP20 EM1


Majority of applications requiring a 50 mm extension

 XY: 0.08 N

 Z: 0.75 N

 Stylus: 10 mm

10 mm to 50 mm

EM2 STD- 75 mm extension

TP20 EM2 module


Majority of applications requiring a 75 mm extension

 XY: 0.08 N

 Z: 0.75 N

 Stylus: 10 mm

10 mm to 50 mm

Change Rack MCR20
The MCR20 probe module changing rack is designed to securely hold stored modules for rapid automatic changing, and to protect them from airborne contaminants which may be present within the working environment.


TP200 Stylus Modules

The stylus module is mounted on the TP200 / TP200B probe body via a highly repeatable magnetic kinematic joint, providing a rapid stylus changing capability and probe overtravel protection.

There are three modules available, with two different overtravel forces.

Module Application Comments
SF (standard force) General use. Styli up to 100 mm long and ball diameter > 1 mm.
LF (low force) Small diameter stylus balls or where minimum force is essential. Balls less than 1 mm diameter.
EO (extended overtravel) Extra overtravel to enable the CMM to stop safely from higher probing speeds. Same overtravel force as SF.
Extra 8 mm of overtravel in probe Z-axis.


SCR200 Change Rack
The SCR200 provides automatic, high speed changing of up to six TP200 stylus modules. The SCR200 is powered by the separate probe interface, PI 200-3, and provides features to facilitate safe stylus changing. The SCR200 is available in low force and standard force kits, where each kit comprises one SCR200 plus three stylus modules of the same force.

 Inquiry - PH10T